4K60 HDBaseT Output Card for Flex Matrix Pro
KanexPro FLEX-PROCAT-OUT for Flex Matrix Pro. CAT (HDBaseT 3.0). 4K60, Dante/AES67, TAA.
Add four CAT (HDBaseT 3.0) outputs to any Flex Matrix Pro chassis. The FLEX-PROCAT-OUT delivers 4K60 4:4:4 at 18Gbps with HDCP 2.2, HDR, scaling, and Dante/AES67 per port. Seamless switching. EDID/HDCP management. Hot-swappable. TAA compliant. 330ft (100m) via CAT6A. PoC supported.
- 4× CAT (HDBaseT 3.0) outputs — hot-swappable across all Flex Pro chassis (16×16 to 128×128)
- 4K60 4:4:4 at 18Gbps • HDCP 2.2 • HDR
- Dante/AES67 network audio • 8ch LPCM High-Res Audio
- Independent scaling per output • seamless switching • EDID/HDCP management
- 330ft (100m) uncompressed 4K60 via CAT6A • PoC • bi-directional RS-232
- Hot-swappable • TAA compliant
Specifications| Input Card ports | 4 X CATx Output Port |
|---|
| Connector Type | RJ45 (Female) |
|---|
| Video Resolution: | Up to 3840x2160 60Hz 4:4:4 (8bit) |
|---|
| Maximum Data Rate | 18 Gbps |
|---|
| HDCP Version : | HDCP 2.2 |
|---|
| Support Hot Plug Detection | Yes |
|---|
| Re-clocking | Output: Automatic |
|---|
| Analog Audio Port | 4 X 3 -pin Phoenix stereo audio for Extraction |
|---|
| PoE port | B ased on IEEE 802.3at, 100 watts , 4 X 2 -pin Phoenix Connector |
|---|
Questions
- How many CAT outputs does the FLEX-PROCAT-OUT provide and what connector does it use?
- The card provides 4 CAT output ports using RJ45 (female) connectors, each carrying a scaled video and audio signal to a Flex Pro CAT receiver.
- What resolution, bandwidth, and HDCP level does the FLEX-PROCAT-OUT support?
- Each output supports video resolutions up to 3840x2160 @60Hz 4:4:4 (8-bit) at a maximum data rate of 18Gbps, with HDMI 2.0 and HDCP 2.2 compliance and HDR support.
- Which receiver connects to the FLEX-PROCAT-OUT card?
- The FLEX-PROCAT-RX (CAT to HDMI receiver) connects directly to the FLEX-PROCAT-OUT card, receiving video with embedded audio and bidirectional RS-232 up to 330 ft (100M) over CAT6A.
- Which Flex Pro chassis models accept the FLEX-PROCAT-OUT card?
- It is hot-swappable across all Flex Pro main frame models: FLEX-PRO16X16, FLEX-PRO32X32, FLEX-PRO64X64, and FLEX-PRO128X128.
- Does the FLEX-PROCAT-OUT card require its own power adapter?
- No local power adapter is documented for the card itself; it is powered by the Flex Pro chassis.
- Can the FLEX-PROCAT-OUT be installed or removed without powering down the chassis?
- Yes. The card is hot-swappable with hot plug and auto detect, so it can be installed or replaced in a Flex Pro chassis card slot without taking the matrix offline.
- There is no signal at a display connected through a FLEX-PROCAT-OUT output. What should I check?
- Confirm a FLEX-PROCAT-RX is connected at the far end and powered, verify the CAT run uses CAT6A and does not exceed 330 ft (100M), and reseat the connection at both ends.
- The Flex Pro chassis does not recognize an installed FLEX-PROCAT-OUT card. What should I do?
- Remove and reseat the card in its slot to trigger hot plug and auto detect; if it is still not recognized, try a different card slot in the chassis.
- Why choose the FLEX-PROCAT-OUT over the FLEX-PROHDMI-OUT or FLEX-PRODP-OUT card?
- The FLEX-PROCAT-OUT extends signal to displays up to 330 ft (100M) over CAT6A, while the FLEX-PROHDMI-OUT and FLEX-PRODP-OUT are intended for local HDMI or DisplayPort connections at the chassis without extension distance.
- What installation scenario is the FLEX-PROCAT-OUT best suited for?
- It suits projects distributing 4K signal from the Flex Pro chassis to displays located beyond typical HDMI cable range, using structured CAT6A cabling to a FLEX-PROCAT-RX at each display.