HDBaseT HDMI Extender over Cat6 - 150M (492 ft.) with PoC
KanexPro EXT-HDBT150M HDBaseT HDMI extender kit: 1080p@60Hz up to 150M (492 ft.) over one Cat6 STP. PoC single PSU, HDMI loop-out, RS-232, IR. 3-year…
The KanexPro EXT-HDBT150M is a professional HDBaseT HDMI extender transmitter-receiver kit that extends 1080p@60Hz HD signals up to 150 meters (492 feet) over a single Cat6 STP cable. With PoC (power over the HDBaseT cable), one locking 24V/1A power supply powers both the TX and RX units over that same Cat6 cable, so no second power run is needed at the remote end. PoC is power over the HDBaseT link, not IEEE 802.3 PoE. Maximum resolution is 1080p@60Hz (HDMI 1.4 / HDCP 1.4, 225MHz per channel, YUV 4:4:4 or RGB 4:4:4). The transmitter includes an HDMI loop-out for local preview monitoring. Bi-directional RS-232 (Phoenix connector) and IR pass-through enable full source and display control from either end of the extension. Full Dolby TrueHD, DTS-HD Master Audio, and LPCM 7.1 audio pass-through are supported. Built to commercial standards with metal enclosure, locking power connector, and ESD protection up to plus or minus 8kV. Backed by KanexPro's 3-year warranty. Applications: Large lecture halls, house of worship, conference rooms, command and control rooms, digital signage, and campus AV where 150M HDBaseT reach and RS-232/IR control are required.
- Extends 1080p@60Hz HDMI over single Cat6 up to 150M (492 ft.) using HDBaseT protocol
- PoC (power over the HDBaseT cable) - one locking 24V/1A supply powers both TX and RX over Cat6
- HDMI loop-out on TX for local preview monitor or secondary display
- Bi-directional RS-232 (Phoenix connector) control pass-through over HDBaseT link
- Bi-directional IR control - wideband IR emitter and receiver cables included
- Full audio: Dolby TrueHD, DTS-HD Master Audio, LPCM 7.1
- HDMI 1.4 / HDCP 1.4 - 225MHz per channel video bandwidth
- ESD protection: plus or minus 8kV air-gap, plus or minus 4kV contact discharge
- Metal enclosure, locking power connector - CE/FCC/UL certified power supply
- 3-year KanexPro parts and labor warranty
Specifications| Protocol | HDBaseT over Cat6 STP |
|---|
| HDMI / HDCP | HDMI 1.4 | HDCP 1.4 | 225MHz per channel |
|---|
| Max Resolution | 1080p@60Hz | YUV 4:4:4 | RGB 4:4:4 |
|---|
| Max Distance | 150M (492 ft.) over Cat6 STP |
|---|
| PoC | Bi-directional - 1 locking PSU powers both units |
|---|
| HDMI Loop-Out | Yes - TX unit |
|---|
| RS-232 | Phoenix connector - bi-directional pass-through |
|---|
| IR | Bi-directional - wideband emitter/receiver included |
|---|
| Audio | TrueHD | DTS-HD MA | LPCM 7.1 |
|---|
| ESD Protection | +/-8kV air-gap | +/-4kV contact discharge |
|---|
| Power | DC 24V/1A locking (1 supply included) |
|---|
| Dimensions | 140 x 65 x 18mm | 406g |
|---|
| Certifications | CE / FCC / UL | 3-year warranty |
|---|
| Operating Temp | 0 degrees C to 40 degrees C |
|---|
| Storage Temp | -20 degrees C to 60 degrees C |
|---|
Questions
- What installs is the EXT-HDBT150M built for?
- Commercial installs needing 1080p HDMI reach beyond typical Cat6 extenders, up to 150M, with a single power supply, RS-232 control, and metal-enclosure ESD protection.
- What is the maximum transmission distance?
- The extender reaches 150M (492 ft.) over Cat6 STP using HDBaseT technology.
- What audio formats pass through?
- Dolby TrueHD, DTS-HD Master Audio, and LPCM 7.1 are supported.
- What is the maximum resolution and video bandwidth?
- The EXT-HDBT150M is HDMI 1.4 / HDCP 1.4 compliant with 225MHz per-channel video bandwidth, supporting 1080p@60Hz in YUV 4:4:4 or RGB 4:4:4, at 8-bit color depth.
- How does the HDMI loop-out fit into the system?
- The TX HDMI LOOP OUT drives a local preview monitor while the extended signal continues to the RX over Cat6.
- How is bi-directional IR wired?
- Connect the included wideband IR emitter and receiver cables to the 3.5mm IR jacks on TX and RX to control source and display from either end.
- How many power supplies are needed?
- Only one locking 24V/1A power supply is required. The unit it is connected to powers the other over the Cat6 cable (PoC: power over the HDBaseT link, not IEEE 802.3 PoE), so no second power run is needed.
- What are the unit dimensions and weight?
- TX and RX each measure 5.51 x 2.56 x 0.71 in (140 x 65 x 18mm) and weigh 0.90 lb (406g).
- RS-232 control is not passing through. What should I check?
- Verify the Phoenix connector wiring between the control system and the extender's Phoenix ports, and confirm the baud rate matches the control system and display. RS-232 passes bidirectionally across the HDBaseT link.
- The RX unit has no power. What should I check?
- Confirm the locking 24V/1A power supply is connected and fully locked (twist clockwise). PoC carries power across the Cat6 link, so if the powered unit is active, the other should receive power automatically; also check Cat6 cable continuity.